How To Jump a Car

For many of us, the prospect of jump-starting our vehicle can be intimidating. While the process is not difficult, if it is done incorrectly it can be dangerous. Being stranded someplace in the street in light of the dead battery isn’t an interesting situation for common drivers. What’s more, in the event that you’ve been there, odds are it could happen to you again.

If you’re the type who just relied on kind people to jump-start the car for you then maybe it’s time to turn things around. Learn how to jump-start the car yourself with these easy steps.

1. Determine the location of your battery. Pop the hood and check which side your battery is located. If you are not sure where it is, consult your owner’s manual. It is also important to determine the location of the battery in the car providing the jump to position it correctly next to yours.

2. Get things ready. To jump-start the car, you need jumper cables, safety glasses and a car that has a fully charged battery with similar voltage as the other car’s dead battery. Although not necessary, you can use a wire brush and rubber gloves. Position the car providing the jump correctly. Nothing is more frustrating than having the car that you are getting a jump from in the wrong location where your jumper cables cannot reach. You should park the car close enough where the jumper cables will reach both cars’ batteries comfortably. Open the hoods on both of your cars and secure them so they will not close. Make sure that the car providing the jump is shut off

3. Examine the battery. Every battery contains electrolyte solution with sulfuric acid. Important: Never jump batteries with a frozen electrolyte or if the battery is frozen. It could cause the battery to explode. You can check whether the electrolyte solution is frozen or not by taking away the detachable vent caps in some batteries. And if you crack in the battery’s casing, don’t jump-start it. Instead, purchase a new one.

4. Ensure that the batteries of the two cars have equal voltage. See to it that the two cars are not touching each other and that each ignition is off.

5. Study the battery. A battery has two poles. One should be marked as positive (+), and the other end is negative (-). You could tell which is the positive terminal since often it comes with a cover and a clump of wires while the negative one comes exposed to only one black cable.

6. Attach cables in a certain order. Using one of the cables, connect one end of it to the positive pole of the dead battery while the other point of that same cable should be connected to the positive pole of the other vehicle. Using another cable, connect one end of it to the starting vehicle’s negative terminal while the other end is attached to the vehicle with a dead battery, particularly to its engine block.

7. Get ready and stand away from the hood of the cars. Put away cigarettes if you’re smoking. Always put on safety glasses as you do this. Get the vehicle with the functioning battery started.

8. Leave it for five minutes. Then start the vehicle that was not starting. If ever it does not work, wait a little longer before doing it again.

9. Start your car. Turn your key in your ignition to see if your car will start. If it does, follow the next steps.

10. Clamp removal. Remove the black clamp from the vehicle providing the car jumping and then the red clamp. Again, do not allow any clamps to touch. Remove the clamps from your car in the same order, black followed by red.

It is important to take your vehicle to your technician after jump starting to determine if you need to replace your battery, battery cables or contacts. It is also recommended that they do a full checkup of your vehicle’s electrical systems to make sure there are not any other factors that led to your battery’s in-operation. Keep this info in your back pocket, and you’ll never have to worry about how to jump-start a stalled car ever again.

What To Do When Your iPhone Won’t Charge

Have you plugged your iPhone into the charger but it doesn’t work? Have you tried switching on and off the switch but nothing works? Have you tried plugging your charging cable into your computer and your iPhone still won’t charge? Well, there could be some issues with your phone that need to be checked immediately. Before you start panicking, here are some tips you should try out to make sure it starts charging again.

1. Hard Reset The Phone
It’s the first thing to do when you find that your iPhone won’t charge. That way, you can identify any software malfunction that might be causing the issue before checking the hardware. Keep in mind that the software on your phone is responsible for charging and not the hardware, so that’s why this is an important first step.

To hard reset your phone, hold down the volume and power button simultaneously for iPhone 7 and the newer versions while for the iPhone 6S and the older versions, you should hold down the power and home button. Press the buttons until the Apple logo appears on the screen and release. Try charging your iPhone again but if it doesn’t work try the remaining tricks. Also, make sure to check out updates covering upcoming fresh bugs and issues with iPhones become

2. Check For Damage On The Charging Cable
Grab the charging cable and check for damage on both sides on the end used for charging. If there are any signs of wear, it could be the reason that your phone isn’t charging. If there’s no visible wear and tear, try charging your phone from a computer rather than directly from a wall socket. Interchange the charging options to find out the culprit. If one of the options charges your phone then there’s no problem with the charging cable. If charging your phone directly from the socket or a computer doesn’t work, you should try charging with a different cable. If it works, then the problem was with your cable.

3. Clean The Phone’s Charging Port
Check the charging port found at the bottom of your phone for any gunk using a flashlight. If there’s any debris, it could be the reason why your phone isn’t charging because the cable doesn’t make a complete connection. Keep in mind that the charging port has 9 connectors so if any of them is blocked by debris, your phone will not charge. Use a soft brush to clean out the gunk and make sure you choose a cleaning brush which won’t conduct electricity.

4. Restore Factory Settings
If your phone is still having issues charging you need to restore the factory settings. Before doing this, you need to make sure everything is backed up in iTunes. A factory reset is also referred to as DFU restore and it restores your iPhone to the original state in which you bought it. Therefore, everything that you have added to your phone since you bought it will be erased completely. Once you have done a factory reset, you should be able to restore everything from iTunes effortlessly and your phone shouldn’t have more issues with charging.

5. Hardware Damage
If your phone still won’t charge, there could be some hardware damage, especially if you spilled some liquid on it. If any liquid comes in contact with the 9 connectors found in your phone’s charging port, then they are completely fried. If that’s the case, you can visit your local Apple store to change the hardware to make sure your phone continues charging. Make sure you disclose the nature of liquid that was spilled on the iPhone to make sure the experts can replace the damaged areas without any further issues.

Tips To Fix Not Charging iPad

Dealing with an iPad plugged in not charging can be an annoying and somewhat scary experience considering how much money you likely invested in it. If you noticed that you plugged in your iPad only to find that it does not charge, you are going to want to utilize some of the top tips to correct the issue. Below, we will be going over some of the top things that you should do in order to find out what’s wrong with it and/or fix it.

Tips To Fix iPad Not Charging Issue:

1. Hard Reset.

This is one of the most surefire ways to fix an iPad or any device that is not charging. Any mobile device can start behaving abnormally for a variety of reasons. Therefore, this is likely going to be the best thing that you can start out with because it is typically the most effective. Simply hold down the ‘sleep/wake button’ and the ‘home button’ at the same time for around 10 seconds each until you see the Apple logo appear on the iPad’s screen. While this is not always going to work, it is typically the most effective way to deal with this sort of problem.

2. Try Another Wall Outlet or USB Port.

Sometimes it might not be the fault of your iPad and instead due to a faulty socket or USB port. Thus, you are going to want to be sure to try this prior to doing anything else with your iPad. The best way to tell if the port isn’t working or if it’s a problem with your cable or device is by using another device and cable with the same outlet or USB port.

3. Check Cable and Connector for Damage.

Another good thing that you are going to want to do to try to pinpoint the issue is to check the cable and connector for damage. By checking the lightning cable, you should be able to tell whether or not there is any apparent damage to it. Because Apple’s lightning cables are very prone to fraying, you want to be sure that you are not experiencing a faulty/bad cable as a direct result of this. If you are attempting to use a bad cable, not only will your iPad likely not charge, but you could be risking damaging your iPad as well.

4. Wait.

A lot of people expect their iPad to turn on right after having the battery drained for a month or more. If you notice that your iPad is not showing a signal of charging right away, simply leave it there and wait for it to show signs of life. Sometimes, it could take up to 30 minutes to see any indication that your iPad is charging. While waiting, check the to work thru the every possible iPad issue checklist.

5. Apple Support.

If all else fails, your last ditch effort will be to call or visit Apple Support. Apple has some of the best support in the tech industry. This is especially true if you purchase Apple Care alongside your iPad. If you did, you can take on your iPad and get it fixed free of charge. If you didn’t, you can still take in your iPad, you will simply be responsible for the cost to fix it. However, you know that you are going to get your iPad fixed by trained technicians by taking it to Apple.

Overall, there is a lot that you can do in order to try to get your iPad to start charging correctly. By implementing the tips above, you should be able to figure out what is wrong with your iPad and in some cases even fix the issue yourself.